[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Date Index][Thread Index][Author Index]

Re: EDP LOOP4 question: Accessing individual loops directly



Thank you, Andy and Bernhard. That was exactly what I found out by  
praxis, but I didn't have the new manual. I only had the printed one  
that came with my EDP from Tace Elliot Ltd. I will immediately read  
this new manual, although my machine is not a "plus" version (any  
difference?).

Trying here to work out performance strategies for Expert Mode  
without using an analog volume pedal. I simply stuck a plug into the  
foot pedal input and use MIDI pedals. Seems to work as far as I can  
see for now. New manual hint comes in very handy. Thanks for the tip,  
Bernhard?  (... BTW - did The Bernhards ever record something?)

/ per




On Sep 13, 2005, at 11:58, Bernhard Wagner LD wrote:

> Hi Per
>
> I think it does. I wanted to reply to your question. I'm a (lucky)  
> PMC-10
> owner with LD list member Sean Echevarria's splendid Raymond editor
> (http://www.creepingfog.com/sean/pmc/raymond.htm) and looked up my  
> patches
> that allow accessing all 16 loops randomly and indeed the first is  
> MIDI note
> 84 (hex 54), the last 99 (hex 63)
>
> But if you check page 7-5 of the edp manual
> (http://www.gibson.com/Files/Downloads/PDFs/Gibson/ 
> EchoplexPlusManual12.pdf)
> it says:
> When multiple loops have been set up with the MoreLoops parameter,
> you can trigger them directly with MIDI Note messages. The LoopTrig
> parameter defines the base Note for Loop 1. The consecutive Loops
> occupy the notes above that, so Loop 2 is LoopTrig+1, Loop 3 is
> LoopTrig+2, etc.
>
> (oops, just saw Andy's post...)
>
> Bernhard
>
>
>> -----Original Message-----
>> From: Per Boysen [mailto:per@boysen.se]
>> Sent: Dienstag, 13. September 2005 11:15
>> To: Loopers-Delight@loopers-delight.com
>> Subject: Re: EDP LOOP4 question: Accessing individual loops directly
>>
>> Found this in the manual:
>>
>>
>>> LoopTrig
>>> The default value for LoopTrig is now 84 to make room for the
>>> expanded MIDI commands.
>>>
>>
>> I have a feeling that this kind of answers my question (below)?
>>
>> / per
>>
>>
>> On Sep 13, 2005, at 9:26, Per Boysen wrote:
>>
>>
>>> Hi,
>>>
>>> Using a midi controller pedal, running my EDP with 76 as the midi
>>> note number offset (parameter "Source #") I was able to directly
>>> access different loops. Like, if using MoreLoops=3, I got:
>>>
>>> note 85 = loop 1
>>> note 86 = loop 2
>>> note 87 = loop 3
>>>
>>> ...etc (I have tried it with up to "MoreLoops = 9".
>>>
>>> Since I can't find anything about this functionality in the LOOP4
>>> manual I wonder: What is it?
>>>
>>> Even more strange it gets when I reduce the "Source #" setting to
>>> zero and the SAME note numbers do still access individual loops!
>>> Are these MIDI note numbers sort of hot wired to individual loops -
>>> no matter what the Source # offset?
>>>
>>> Greetings from Sweden
>>>
>>> Per Boysen
>>> www.looproom.com (international)
>>> www.boysen.se (Swedish)
>>> --->  iTunes Music Store (digital)
>>> www.cdbaby.com/perboysen
>>>
>>>
>>>
>>>
>
>
>
>