Looper's Delight Archive Top (Search)
Date Index
Thread Index
Author Index
Looper's Delight Home
Mailing List Info

[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Date Index][Thread Index][Author Index]

RE: Troubleshooting my EDPs and FCB....Again (factory reset guidance)



Torstein - Before I get to working on my FCB, I'll post the parameters
that fixed my drift problems several months ago...haven't had any
problems since then....I use the TSR cable connect the two units via
Brother Sync, plus run MIDI out from one to the MIDI in of the other.

Kris

Parameter settings for both units, horizontal across the unit, left to
right: 

Loops 

MoreLoops=2L 
AutoRecord=ON 
LoopCopy=OFF 
SwitchQuant=LOP 
LoopTrig#=84 
Velocity=OFF 
SamplerStyle=RUN 

MIDI 

Channel=1 
ControlSource=Ctr (FIRST CRITICAL SETTING, AS STATED IN MANUAL...could
be "not" as well) 
Source#=36 
VolumeCont=7 
FeedBkCont=1 
Dump=001  h 
Load=001  - 

Switches 

RecordMode=tOG 
OverdubMode=tOG 
RoundMode=OFF 
InsertMode=rEV 
MuteMode=StA 
Overflow=PLY 
Presets=Pr.E 

Timing 

Loop/Delay=LOP 
Quantize=OFF 
8ths/Cycle=1 
Sync=OUT (SECOND CRITICAL SETTING, AS STATED IN MANUAL) 
Threshold=0 (THIRD CRITICAL SETTING, NOT IN MANUAL...NEEDS TO BE SET TO
0) 
Reverse=[Shows No Setting] 
StartPoint=[Shows No Setting, but "1" at the first LED] 


-----Original Message-----
From: Torstein H. Rem [mailto:thelgere@online.no] 
Sent: Sunday, July 10, 2005 12:24 PM
To: Loopers-Delight@loopers-delight.com
Subject: Re: Troubleshooting my EDPs and FCB....Again (factory reset
guidance)

To Kris an others with two EDP`s.

While talking about syncing two EDP`s I``ll use the chance to ask about
sync problems.
Even when hooked up right I have problems. For each repeat of a loop the
soundstage will drift over to one side more and more and getting out of
phase. Next time (loop) it might drift over to the other side. More or
less randomly.
This has been discussed before, I believe. Someone installed some new
clock(s) ?
What to do about it?
Both my EDP`s are from the same period (beige Gibson).

Thanks!
T.



----- Original Message -----
From: "Hartung, Kris" <kris.hartung@hp.com>
To: <Loopers-Delight@loopers-delight.com>
Sent: Sunday, July 10, 2005 7:39 PM
Subject: RE: Troubleshooting my EDPs and FCB....Again (factory reset
guidance)


I'll give it a try. I was wondering, since my problem only occurs with
both units, what about using my MIDI splitter to go from the FCB to the
EDPs, rather than to one EDP and then MIDI out of that one to the next?
I would still use the Brother Sync of course.

Kris


-----Original Message-----
From: Per Boysen [mailto:per@boysen.se]
Sent: Sunday, July 10, 2005 4:09 AM
To: Loopers-Delight@loopers-delight.com
Subject: Re: Troubleshooting my EDPs and FCB....Again (factory reset
guidance)

On Jul 10, 2005, at 11:57, Hartung, Kris wrote:

> Before I start troubleshooting in detail, I thought I would try 
> resetting the FCB to factory state first. However, I am confused by 
> what the manual says about this. It shows three ways to perform a 
> factory
> reset: V-AMP family products, BEHRINGER guitar amps, and  BASS V-AMP 
> product range. Is there a particular reset option I should choose?


No. Whatever reset you use you will have to empty the banks and put in
new data for the EDP. When programming your FCB banks you must be aware
of that the FCB can send multiple midi commands on every button press.
In the FCB patch programming mode you have to disable everything except
for what the EDP needs. Otherwise you will go nuts when trying to get it
right ;-)

Greetings from Sweden

Per Boysen
www.looproom.com (international)
www.boysen.se (Swedish)
--->  iTunes Music Store (digital)
www.cdbaby.com/perboysen